Forged Eye Bolt
|
|
|
Regular Nut Eye Bolt
G-291 |
Shoulder nut Eye Bolt
G-277 |
Machiner Eye Bolt
S-279/ M-279 |
WARNING |
•Loads may slip or fall if proper eye bolt assembly and lifting procedures are not used.
•A falling load can seriously injure or kill.
•Read and understand both sides of these instructions, and follow all eye bolt safety information presented here.
•Read, understand, and follow information in diagrams and charts below before using eye bolt assemblies. |
Important Safety Information -Read & Follow
Inspection/Maintenance Safety:
•Always inspect eye bolt before use
•Never use eye bolt that shows signs of wear or damage.
•Never use eye bolt if eye or shank is bent or elongated.
•Always be sure threads on shank and receiving holes are clean.
•Never machine, grind, or cut eye bolt.
Assembly Safety:
•Never exceed load limits specified in Table I & Table 2.
•Never use regular nut eye bolts for angular lifts.
•Always use shoulder nut eye bolts (or machinery eye bolts) for angular lifts.
•For angular lifts, adjust working load as follows:
Direction of Pull (in-line) |
Adjusted Working Load |
45 degrees |
30% of rated working load |
90 degrees |
25% of rated working load |
•Never undercut eye bolt to seat shoulder against the load.
•Always countersink receiving hole or use washer with sufficient I.D. to seat shoulder.
•Always screw eye bolt down completely for proper seating.
•Always tighten nuts securely against the load.
Tabela 1 (obciążenie w linii) |
Wymiar
(mm) |
Dopuszczalne
Obciążenie
Robocze
(kG) |
6.35 |
295 |
7.94 |
544 |
9.53 |
703 |
12.7 |
1179 |
15.9 |
2351 |
19.1 |
3266 |
22.2 |
4808 |
25.4 |
6033 |
31.8 |
9525 |
38.1 |
10886 |
|
Tabela 2 (obciążenie w linii) |
Wymiar
(mm) |
Dopuszczalne
Obciążenie
Robocze
(kG) |
m6 |
200 |
m8 |
400 |
m10 |
640 |
m12 |
1000 |
m16 |
1800 |
m20 |
2500 |
m24 |
4000 |
m30 |
6000 |
m36 |
8500 |
|
|
|
Shoulder Nut Eye Bolt - Installation for Angular Loading
IMPORTANT - Read and understand these instructions before using eye bolts. Regular Nut & Shoulder Nut Eye Bolt - Installation for In-line Loading
Operating Safety
•Always stand clear of load.
•Always lift load with steady, even pull - do not jerk.
•Always apply load to eye bolt in the plane of the eye - not at an angle.
•Never exceed the capacity of the eye bolt-see Table I & 2.
•When using lifting slings of two or more legs, make sure the loads in the legs are calculated using the angle from the vertical to the leg and properly size the shoulder nut or machinery eye bolt for the angular load.
Machinery Eye Bolt - Installation for In-line & Angular Loading
These eye bolts are primarily intended to be installed into tapped holes.
1. After the loads on the eye bolts have been calculated, select the proper size eye bolt for the job.
For angular lifts, adjust working load as follows:
Direction of Pull |
Adjusted Working Load |
45 degrees |
30% of rated working load |
90 degrees |
25% of rated working load |
-
Drill and tap the load to the correct sizes to a minimum depth of one-half the eye bolt size beyond the shank length of the machinery eye bolt.
-
Thread the eye bolt into the load until the shoulder is flush and securely tightened against the load.
-
If the plane of the machinery eye bolt is not aligned with the sling line, estimate the amount of unthreading rotation necessary to align the plane of the eye properly. Remove the machinery eye bolt from the load and add shims (washers) of proper thickness to adjust the angle of the plane of the eye to match the sling line. Use Table 3 to estimate the required shim thickness for the amount of unthreading rotation required.
Table 3 |
Eye Bolt Size
(in.) |
Shim Thickness
Required Change
Rotation 90
(in.) |
Eye Bolt
Size
(mm) |
Shim Thickness
Required to change
Rotation 90
(mm) |
1/4 |
.0125 |
M6 |
.25 |
5/16 |
.0139 |
M8 |
.31 |
3/8 |
.0156 |
M10 |
.38 |
1/2 |
.0192 |
M12 |
.44 |
5/8 |
.0227 |
M16 |
.50 |
3/4 |
.0250 |
M20 |
.62 |
1/8 |
.0278 |
M24 |
.75 |
1 |
.0312 |
M27 |
.75 |
1-1/8 |
.0357 |
M30 |
.8 |
1-1/4 |
.0357 |
M36 |
1.00 |
1-1/2 |
.0417 |
- |
- |
1-3/4 |
.0500 |
M42 |
1.13 |
2 |
.0556 |
M48 |
1.25 |
2-1/2 |
.0625 |
M64 |
1.50 |
|